dimensions: [mm] properties value unit tol. diameter ? d 35 mm 1 length l 35 mm 2 dimensions: recommended hole pattern: [mm] schematic: properties test conditions value unit tol. capacitance 0.25 v/ 120 hz/ +20 c c 470 f 20% rated voltage u r 400 v (dc) max. leakage current 5 min./ +20 c i leak 1300.77 a max. dissipation factor 0.25 v/ 120 hz/ +20 c df 20 % max. ripple current 120 hz @ 85 c i ripple 2510 ma max. electrical properties: aluminum electrolytic capacitors storage conditions 5-35 c, < 75% rh operating temperature -25 c up to +85 c endurance 3000 h @ / 400 v (dc) / max. iripple test conditions of electrical properties: +20c, 35% rh if not specified differently fit according to separate documentation component conform to reach and rohs requirements and standards general information: wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-aie8 aluminum electrolytic capacitors anaq350471m400dsic2c000 order code 861221386021 size revision status date (yyyy-mm-dd) business unit page 35 x 35 001.000 valid 2017-01-20 eicap 1/8 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. o d l 6,0 1 detail a - + 1 0 , 0 0 , 2 vent under cover a o 2,0 10,0 0,2
instruction for optional fixation: wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-aie8 aluminum electrolytic capacitors anaq350471m400dsic2c000 order code 861221386021 size revision status date (yyyy-mm-dd) business unit page 35 x 35 001.000 valid 2017-01-20 eicap 2/8 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. sectional drawing a-a capillary joint fixing material fixing material max. 80% detail c fixing material detail b a a b c 0 , 8 0 , 1 2,5 0,1 1,5 0,1 6,0 1
1 st line capacitance value: 470 f & rated voltage: 400 v (dc) 2 nd line wcap-aie8 3 rd line vent marking & max. operating temperature 4 th line negative pin marking component marking: c [f]/ frequency [hz] 50 (60) 120 1k 10k 50k-100k 10 c 100 0.80 1.00 1.36 1.48 1.53 100 < c 1000 0.80 1.00 1.25 1.35 1.38 1000 < c 0.80 1.00 1.17 1.25 1.28 multiplier for ripple current vs. frequency wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-aie8 aluminum electrolytic capacitors anaq350471m400dsic2c000 order code 861221386021 size revision status date (yyyy-mm-dd) business unit page 35 x 35 001.000 valid 2017-01-20 eicap 3/8 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
classification wave soldering profile: profile feature pb-free assembly sn-pb assembly preheat temperature min t s min 100 c 100 c preheat temperature typical t s typical 120 c 120 c preheat temperature max t s max 130 c 130 c preheat time t s from t s min to t s max t s 70 seconds 70 seconds ramp-up rate t 150 c max. 150 c max. peak temperature t p 250 c - 260 c 235 c - 260 c time of actual peak temperature t p max. 10 seconds max. 5 seconds each wave max. 10 seconds max. 5 seconds each wave ramp-down rate, min ~ 2 k/ second ~ 2 k/ second ramp-down rate, typical ~ 3.5 k/ second ~ 3.5 k/ second ramp-down rate, max ~ 5 k/ second ~ 5 k/ second time 25c to 25c 4 minutes 4 minutes classification wave soldering profile: refer to en61760-1:2006 wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-aie8 aluminum electrolytic capacitors anaq350471m400dsic2c000 order code 861221386021 size revision status date (yyyy-mm-dd) business unit page 35 x 35 001.000 valid 2017-01-20 eicap 4/8 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. temperature time t p t p t s max t s typical t s min first wave preheat area cool down area second wave typical temperature procedure min temperature procedure max temperature procedure
cautions and warnings: the following conditions apply to all goods within the product series of wcap-aie8 of wrth elektronik eisos gmbh & co. kg: 1.01 polarity an aluminum electrolytic capacitor has a polarity. in operation this polarity needs to be considered and adhered. reverse voltage can damage or destroy an aluminum electrolytic capacitor. this can finally lead to a malfunction. if the polarity in a circuit will be switched or possibly can be reversed, the usage of a non-polar capacitor shall be applied. the polarity of an electrolytic capacitor is for snap-in types marked like following. a minus sign on one of the claw fasteners indicates the negative terminal. on the sleeve the negative terminal is marked with a color band and thereon are minus signs given. 1.02 overvoltage avoid any overvoltage and do not apply a continuous overvoltage. if an overvoltage is applied to the capacitor, the leakage current can increase drastically. the applied working voltage is not allowed to exceed the rated working voltage of the specific capacitor. 1.03 operating temperature the capacitor shall not be operated above the operating temperature, which is stated within this datasheet of the specific capacitor. the achievable lifetime of the capacitor is correlating to the applied temperature. in order to achieve the maximum lifetime, the capacitor should be operated by the lowest possible temperature conditions within the application. 1.04 ripple current the applied ripple current shall not exceed the specified maximum ripple current of the capacitor. if a higher ripple current is applied as permitted, it can cause excessive heat generation and higher temperature inside the capacitor. this happens due to pole change effects, if ripple current is applied to the capacitor. this can result in damage or lifetime shortage of the capacitor and may cause deterioration. electrolytic capacitors are regularly not designed for usage in ac applications and ripple current is applied / based due to parasitic effects on dc signal. please see electrical specification within this datasheet for maximum allowed ripple current. 1.05 charge and discharge frequent and quick charge / discharge cycles may generate heat inside the capacitor. in worst case this can cause a decrease of capacitance, an increase of leakage current or breakdown. applications with rapid charge and discharge cycles should be avoided. for assistance with your application please consult our technical support. 1.06 vent on most aluminum electrolytic types, a predetermined breaking point is given on the top of the component, which is the so called vent. the vent is there to assure a possible pressure relief and to avoid that the capacitor can explode due to internal pressure, which can occur by applying reverse voltage or a too high ripple current. a space of at least 3mm above the vent is recommended, in order to assure the full function of the vent. if less space is present the vent maybe cannot operate correctly / completely. 1.07 sleeve the sleeve material consists of pet (polyethylene terephthalate). if excessive heat is applied to the sleeve (e.g. soldering process, etc.) the sleeve may crack or deform. if the capacitor will be exposed to xylene, toluene or likewise and will be afterwards heated, the sleeve may crack or deform. the sleeve does not assure any electrical insulation. it is to avoid to use / place the product on a spot where electrical insulation is needed. to assure electrical insulation, especially to the case of capacitor, further actions need to be taken. 1.08 storage conditions the storage conditions for a capacitor are recommended to be 5 c up to 35 c and less than 75 % rel. humidity. do not expose the capacitor to environments with hazardous gas, ozone, ultraviolet rays or any kind of radiation. avoid any contact of the capacitor with direct sunshine, saltwater, spray of water or types of oil during storage.. if a capacitor is stored for a long time without applying voltage or storage conditions of 35 c or above and more than 75 % relative humidity, the leakage current may increase. the leakage current will return to normal level when applying the rated voltage to the capacitor before use. if the capacitor was stored for more than 6 months, it is recommended to apply dc working voltage to the capacitor for 30 minutes through a 1 k protective series resistor. wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-aie8 aluminum electrolytic capacitors anaq350471m400dsic2c000 order code 861221386021 size revision status date (yyyy-mm-dd) business unit page 35 x 35 001.000 valid 2017-01-20 eicap 5/8 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
all products shall be used before the end of the period of 12 months based on the product date code, if not a 100 % solderability cannot be guaranteed. the capacitance tolerance as specified within the datasheet is only valid on the date of delivery. 1.09 wave soldering the detailed soldering instruction is given within soldering specification in this datasheet. during wave soldering only the pins / terminals should have contact with hot solder bath / wave. assure that no direct contact of capacitor body with hot solder bath / wave or any other component will happen. soldering must be done from the opposite pcb side where capacitor body is placed. 1.10 iron soldering take care that the tip of solder iron will only contact pins or leadframe of the capacitor to avoid any possible damage of the capacitor. 1.11 cleaning do not wash the assembled capacitors with the following cleaning agents: ? petroleum system solvents: may cause degeneration of the rubber seal material ? alkali system solvents: may cause corrosion and dissolve of the aluminum case ? halogenated solvents: may cause corrosion and failure of the capacitor ? acetone: component marking may be erased ? xylene: may cause deterioration of the rubber seal material verify the following points when washing is are applied to capacitors: please monitor conductivity, ph-value, specific gravity and the water content of cleaning agents. contamination adversely affects these characteristics. be sure to not expose the capacitors under solvent rich conditions or keep capacitors inside a closed container. in addition, please dry the solvents on the pcb and the capacitor sufficiently with an air knife (temperature should be less than the maximum rated category temperature of the capacitor) for 10 minutes. capacitors can be characteristically and catastrophically damaged by halogen ions, particularly by chlorine ions. the degree of the damage mainly depends upon the characteristics of the electrolyte and rubber seal material. when halogen ions come into contact with the inside of the capacitors, the foil may corrode, when a voltage is applied. this corrosion causes an extremely high leakage current, which results in venting and an open circuit defect. all other cleaning processes and cleaning agents are not approved by wrth elektronik eisos. all cleaning methods need to be tested and validated by the customer. 1.12 adhesives and coating materials the usage of any adhesive or coating material, which is containing halogenated solvents, is not allowed. before applying adhesives or coating materials, make sure that the following points are fulfilled: ? take care that the surface and capacitor is dry and clean before applying adhesive or coating, to avoid any contamination with flux residues or cleaning solvents. ? assure that no flux residue or spot is left between the rubber seal material of the capacitor and the pcb. ? do not fully cover the entire rubber seal surface with adhesive, coating or molding materials. otherwise the covering of the full rubber seal surface may restrain the natural diffusion of hydrogen gas. block maximum 80% of the sealed section of a capacitor. ? if the used adhesive, coating or molding material is containing halogen ions in a large amount, the halogen ions can diffuse and creep into the capacitor and can damage the capacitor. both above explained circumstances can result in serious failures. ? follow the specified heating and curing instructions given by supplier of the used adhesive or coating material. avoid excessive pressure or heat on the capacitor by applying coating or adhesive. ? take care that hardening of adhesive, coating material was correctly done, so that no solvents do remain. ? be aware, that used solvents within adhesive and coating materials can damage the sleeve of the capacitor and can result in changes of the appearance of the sleeve (color, shine and marking). 1.13 mechanical stress on lead wire and terminal do not stress the capacitor with the following actions: ? applying any excessive force to the lead wire or terminal. ? move or turn the capacitor after soldering to the pcb. ? bending pins after soldering. ? carrying the pcb by picking / holding the board via a capacitor. 1.14 operation and usage of the capacitor in operation and usage take care about the following points. do not use the capacitor within the following environmental conditions: ? environment with high mechanical stress / shocks or vibration (please see this specific datasheet for permitted limits). ? environment with high amount of damp condensation, water or types of oil. ? direct sunlight, ozone, any kind of radiation or ultraviolet rays. wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-aie8 aluminum electrolytic capacitors anaq350471m400dsic2c000 order code 861221386021 size revision status date (yyyy-mm-dd) business unit page 35 x 35 001.000 valid 2017-01-20 eicap 6/8 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
? toxic gases (e.g. ammonium, chlorine and compounds, bromine and compounds, hydrogen sulfide, sulfuric acid). user should never touch the terminals of the capacitor directly. avoid short circuit between terminals with any kind of conductive material (e.g. metal, fluid, acid, alkaline solution). 1.15 maintenance for industrial applications it is recommended to perform periodic inspections. power supplies shall be turned off before inspection to discharge the capacitor. check the following points in case of an inspection: ? visual inspection of the capacitor to see, if the vent operated for pressure relief and if any leakage of electrolyte has taken place. ? measurement of electrical characteristics of the capacitor (according to datasheet, especially leakage current, capacitance and dissipation factor). in case of deviation or failure according to the specified characteristics, take care to start appropriate actions (e.g. replacement of capacitor). 1.16 emergency case in case of excessive pressure within the capacitor the vent may operate and release this pressure. in case of vent operation gas becomes visible, when the component is in operation. if so, directly turn off the application and disconnect it from the power source. if the application will not be turned off, a possible short circuit of capacitor or a short circuit due to bridging of liquefied gas can possibly damage the circuit and in worst case the application may be dramatically damaged. do not stay or position body or face above or in direction of the vent, because in the event of any vent operation, the releasing gas temperature may have over 100 c. in case of contact with the electrolyte on skin, wash the skin immediately with soap and water. if the eyes will get in contact with the releasing gas, immediately wash the eyes with water. whether the gas was inhaled, directly use gargle. 1.17 disposal please contact your local responsible or organization for proper disposal of capacitor. also take care to be compliant in order to your local governmental law and restrictions. in case incineration, it should be done with more than 800 c. lower temperatures at incineration can result in toxic gases (e.g. chlorine). to avoid any explosion of capacitor, punch holes into the can or crush the capacitor before incineration. wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-aie8 aluminum electrolytic capacitors anaq350471m400dsic2c000 order code 861221386021 size revision status date (yyyy-mm-dd) business unit page 35 x 35 001.000 valid 2017-01-20 eicap 7/8 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
important notes the following conditions apply to all goods within the product range of wrth elektronik eisos gmbh & co. kg: 1. general customer responsibility some goods within the product range of wrth elektronik eisos gmbh & co. kg contain statements regarding general suitability for certain application areas. these statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. the responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not. 2. customer responsibility related to specific, in particular safety-relevant applications it has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications. in certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. therefore, customer is cautioned to verify that data sheets are current before placing orders. the current data sheets can be downloaded at www.we-online.com. 3. best care and attention any product-specific notes, cautions and warnings must be strictly observed. any disregard will result in the loss of warranty. 4. customer support for product specifications some products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. necessary information is available on request. in this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter. 5. product r&d due to constant product improvement product specifications may change from time to time. as a standard reporting procedure of the product change notification (pcn) according to the jedec-standard inform about minor and major changes. in case of further queries regarding the pcn, the field sales engineer or the internal sales person in charge should be contacted. the basic responsibility of the customer as per section 1 and 2 remains unaffected. 6. product life cycle due to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. as a standard reporting procedure of the product termination notification (ptn) according to the jedec-standard we will inform at an early stage about inevitable product discontinuance. according to this we cannot guarantee that all products within our product range will always be available. therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. the approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 7. property rights all the rights for contractual products produced by wrth elektronik eisos gmbh & co. kg on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with wrth elektronik eisos gmbh & co. kg. wrth elektronik eisos gmbh & co. kg does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which wrth elektronik eisos gmbh & co. kg components or services are used. 8. general terms and conditions unless otherwise agreed in individual contracts, all orders are subject to the current version of the general terms and conditions of wrth elektronik eisos group, last version available at www.we-online.com. wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-aie8 aluminum electrolytic capacitors anaq350471m400dsic2c000 order code 861221386021 size revision status date (yyyy-mm-dd) business unit page 35 x 35 001.000 valid 2017-01-20 eicap 8/8 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
|
